full service NDT din 1990

ET EtherNDE Instruments

Defectoscop eddy curents portabil - VANTAGE

The ETher Vantage is a handheld, full featured Eddy Current Flaw Detector, which allows for single handed operation, leaving the operator free to use the other hand to scan with a probe.

The Vantage specifications and features are comprehensive and will appeal to users in Aerospace, Offshore, Petrochemical, Power Generation and Rail / Axel Inspection industries. With a full color display and a compact and robust enclosure, the Vantage is ideal for use in on-site and factory environments.

Features:

  • USB Port allows trouble free data transfer and software upgrades.
  • Signal-to-noise ratio is excellent, allowing greater probability of flaw detection and the Vantage performs well with Rotating, Pencil, Weldscan and other probes.
  • Frequency Range is 50Hz - 12MHz and test modes can be Dual Frequency (F1 and F2) or Mix (in 4 configurations)
  • Three Alarm shapes are offered and can be used for F1, F2 or Mix respectively.
  • Data processing rate is up to 6kHz and allows storage of 200+ screen recordings of up to 40 seconds each.   

 

ET EtherNDE instruments VANTAGEET EtherNDE instruments VANTAGE

 

The Vantage is a true handheld Flaw Detector, weighing just 13/4 pounds (0.8 kg) and is well balanced, allowing comfortable operation over the duration of a shift. Housed in a rugged ABS enclosure meeting IP65 splash proof requirements, the Vantage will withstand the harshest of site environments. Incorporating a Nickel Metal-Hydride Battery Pack, 6  hour battery life is typical in the standard modes and 4 hours in rotary mode.  

 

The display screen is 320 x 240 pixels providing excellent resolution aiding accurate and rapid defect interpretation. The user interface incorporates a simple side-bar menu allowing direct access to key instrument parameters that can be instantly switched to full-screen mode. The menu system is intuitive and any experienced Eddy Current operator will quickly be comfortable with this instrument. A time-based strip chart is available to assist with faster and more reliable defect detection. 

 

ET EtherNDE instruments VANTAGEET EtherNDE instruments VANTAGE

The instrument has a single pin Lemo 00 Connector for absolute probes.

A 14 pin Connector for Rotary, Bridge and Reflection Probes.

A USB Port for connection to a  PC.The USB cable and reporting software is included at no additional cost. 

 

Specifications

Inspection Technology: Eddy Current
Operating Frequencies: 60kHz, 120kHz, 240kHz, 480kHz and 960kHz
Conductivity Range: 0.5% IACS to 110% IACS, 0.28 - 64 MS/m
Accuracy: At 68°F / 20°C. At 10% IACS: ± 0.1% IACS
At 212°F / 100°C IACS: ± 0.5% IACS
Over Range 0 - 104°F / 0 - 40°C: At 10% IACS
± 0.2% IACS. At 100% IACS: ± 0.8% IACS
Probe in thermal equilibrium with metal 
Display Resolution: Up to 3 decimal places
Lift Off: 0.5" / 13mm probe compensated to 0.020" (0.5mm)
0.28" / 7mm probe compensated to 0.010" (0.25mm)
Temperature Measurement: In probe sensor (accurate to 32.9°F / 0.5°C), Range 0° to 122°F / 0°C to 50°C 
Automatic Temperature Compensation: Conductivity measurements are corrected to the 68°F / 20°C value
Environmental Range: o to 95% relative humidity,0°F to 122°F / 0°C to 50°C for reliable operation
Display: 2.8" (70mm), 320 x 240 pixels color display, LCD with selectable backlight
Construction & Storage: High impact, splash-proof, molded UL94 - 5VA flame retardant ABS case. Protective Rubber boot to protect the unit, probes, probe cable, operator manual on USB and removable stand.
Conductivity Standards: On top of the unit. Removable for value verification and when attached ensures thermal equilibrium.
Power: 2 x 1.5V AA NiMH Batteries, Approximately up to 6 hrs lifespan. Can also use non-rechargeable AA cells.
Size: 0.5" x 0.27" x .08" (163 x 80 x 25 mm) (L x W x D)  
Weight: 0.77 lbs. (350 g.) including batteries
Data Logger Memory: Removable 2GB micro SD Card allowing over 1 million readings to be stored.
PC Connectivity: USB port for charger and PC communications
Probes: 0.5" / 12.7mm diameter for 60kHz to 480kHz.
0.28" / 7mm probe operates at 480kHz & 960kHz.
Probes are interchangeable with simple operator resetting procedures. Probes are field exchangeable and do not require return to manufacturer for calibration. 
Accessories: Settings Reference Blocks - a range of conductivity reference standards traceable to US and European standards are available for in-field use. Up to 5 can be mounted on an aluminum anodized holding plate.

 

Ask yourself what you are interested in, call or use the contact form at the bottom of the page.

Trimite email. Toate campurile cu (*) sunt obligatorii.
Adress PTS România
  str. Uranus nr. 9,
  bl. 9, sc. A , ap. 4
  500 361 Brașov
Phone +40 754 453 231
E-mail: